Mohsen Mohammadi

Research interests

• Metal Additive Manufacturing
• 3D Printing of Composites
• Cognitive Sensitive Design
• Fatigue, Fracture, and Failure of Materials
• Crystal Plasticity Modeling of Metals
• Micromechanical Modeling of Composites
• Finte Element Analysis

Selected publications

A. Hadadzadeh, B. Shalchi Amirkhiz, S. Shakerin, J. Kelly, J. Li, M. Mohammadi, “Microstructural investigation and mechanical behavior of a two-material component fabricated through selective laser melting of AlSi10Mg on an Al-Cu-Ni-Fe-Mg cast alloy substrate”. Additive Manufacturing, Vol. 31, 2020, 100937.

C. Dharmendra, A. Hadadzadeh, B. Shalchi Amirkhiz, G.D. Janaki Ram, M. Mohammadi, “Microstructural evolution and mechanical behavior of nickel aluminum bronze Cu-9Al-4Fe-4Ni-1Mn fabricated through wire-arc additive manufacturing”. Additive Manufacturing,Vol. 30, 2019, 100872.

S. Shakerian, A. Hadadzadeh, B. Shalchi Amirkhiz, S. Shamsdini, J. Li, M. Mohammadi, “Additive Manufacturing of Maraging Steel-H13 Bimetals Using Laser Powder Bed Fusion Technique”. Additive Manufacturing, Vol. 29, 2019, 100797.

P. Fathi, M. Mohammadi, X. Duan, A. Nasiri, “On microstructure and corrosion behaviour of AlSi10Mg alloy with low surface roughness fabricated by direct metal laser sintering”. Corrosion Science, Vol. 157, 2019, 126-145.

A. Hadadzadeh, B. Shalchi Amirkhiz, A. Odeshi, J. Li, M. Mohammadi, “Role of hierarchical microstructure of additively manufactured AlSi10Mg on dynamic loading behavior”. Additive Manufacturing, Vol. 28, 2019, 1-13.

A. Hadadzadeh, B. Shalchi Amirkhiz, A. Odeshi, M. Mohammadi, “Dynamic loading of direct metal laser sintered AlSi10Mg alloy: Strengthening behavior in different building directions”. Materials & Design, Vol. 159, 2018, 201-211.

A. Hadadzadeh, B. Shalchi Amirkhiz, J. Li, M. Mohammadi, “Columnar to equiaxed transition during direct metal laser sintering of AlSi10Mg alloy: effect of building direction”. Additive Manufacturing, Vol. 23, 2018, 121-131.

A. Hadadzadeh, C. Baxter, B. Shalchi Amirkhiz, M. Mohammadi, “Strengthening mechanisms in direct metal laser sintered AlSi10Mg: Comparison between virgin and recycled powders”. Additive Manufacturing, Vol. 23, 2018, 108-120.

A. Ebrahimi, M. Mohammadi, “Numerical tools to investigate mechanical and fatigue properties of additively manufactured MS1-H13 hybrid steels”. Additive Manufacturing, Vol. 23, 2018, 381-393.

H. Asgari, C. Baxter, K. Hosseinkhani, M. Mohammadi, “On microstructure and mechanical properties of additively manufactured AlSi10Mg_200C using recycled powder”. Materials Science and Engineering A, Vol. 707, 2017, 148-158.

H. Asgari, M. Mohammadi, “Microstructure and mechanical properties of stainless steel CX manufactured by Direct Metal laser Sintering”. Materials Science and Engineering A, Vol. 709, 2018, 82-89.

M. Mohammadi, H. Asgari, “Achieving low surface roughness AlSi100Mg_200C parts using direct metal laser sintering”. Additive Manufacturing, Vol. 20, 2018, 23-32.